|Other Name:||Peeler Centrifuge||Warrenty:||12 Months|
|Color:||Blue Or As Request||Operation:||Switch Between Automatic And Manual|
Horizontal Peeler Centrifuges,
Complete Continuous Horizontal Peeler Centrifuges,
Sulphuric Ammonia Separation Peeler Centrifuges
Complete Continuous Horizontal Peeler Centrifuges for Sulphuric Ammonia Separation
Working Principle and Operating Process
when the machine is in operation, the drum runs at full speed. The water (filtrate) is filled into the siphon chamber through backwash pipe. Through the hole between the drum and the siphon chamber, the liquid is pressed into the drum. Water ring formed by the liquid in the high-speed rotating drum and the siphon chamber, not only venting the air in the siphon chamber but also form a liquid layer on the filter media to ensure the evenly distribution of the feeding liquid.
Start feeding and rotate the siphon down to a certain middle position. After a certain period of time, rotate it to the specified lower position. After feeding, rotate the siphon to the lowest position.
After the suspension enters the drum, the solids are trapped on the press cloth, while the liquid passes through the filter cloth and the filter plate under the cloth It flows into the siphon chamber through the passage between the inner wall of the drum and sucked away by the siphon.
The solids trapped on the press cloth are dehydrated for a certain period of time, and then the materials are scraped by a scraper and slid out of the machine through a hopper.
After discharging is finished, start washing mesh, the siphon scraper centrifuge is different from ordinary scraper centrifuge, the filter cloth can be rinsed not only from above but also from below. In other words, the backwash pipe is used to add washing water into the siphon chamber, and the washing water flows into the drum and flows from the bottom of the filter cloth to the top of the filter cloth to achieve the purpose of reverse washing.
|Drum diameter||800 mm , about 31.5 inch|
|Drum length||450 mm , about 17.7 inch|
|Block liquid port diameter||600 mm , about 23.6 inch|
|Drum speed||1550 rpm|
|Maximun separation factor||1070|
|Motor power||45 Kw|
|Loading capacity||150 Kg|
The GKH800-NA centrifuge is a siphon scraper discharge centrifuge. The machine is equipped with a PC, and the working process is automatically controlled.
In addition to centrifugal force, there is a vacuum siphon suction force for the dehydration of liquid, which has higher production capacity and separation and washing effect compared with the common scraper discharge filtration centrifuge.
This machine has a wide range of application, besides the material separated by the common scraper discharge filtration centrifuge, it is also suitable for materials with small solid particles and difficult to be separated, such as starch, calcium phosphate, etc.
During the operation of the machine, all processes, such as main feed, auxiliary feed, discharge and recoil, are completed at the working speed.
1. The scraper centrifuge can be switched between automatic and manual operation, so it can realize the periodic cyclic operation of feeding, dehydration, washing and discharging of the feed material.
2. The filter speed can be adjusted at will, which makes the feeding liquid evenly distributed on the filter media, and the vibration and noise of the machine are greatly reduced
3. The electric control adopts the advanced programmable logic controller (PLC), which is small and the control movement is accurate and reliable. It is easy to maintain with high efficiency and long service life
1 ) This centrifuge has higher production capacity than common scraper centrifuge and the moisture content of filter cake is lower.
2 ) Material for the components touching the products and the mother liquid can be chose and supplied by the customers according to the erosion of the products. Manufacturers should assist customers to make reasonable choices. Final decision is subject to the attachment of the contract. Commonly the material can be 0Cr19Ni9,321,316L,TA2,C276 and duplex steel.
3 ) Use advanced programmable logic controller (PC) to control electric control, it’s has many advantages such as movements are accurate and reliable, small size, easy adjustment and maintenance, high efficiency and long life.
4 ) Several interlock control devices highly improve the security of the machine.
5 ) Floating platform and shock absorber need to be installed to the bottom of the centrifuge to reduce damages of vibration to the plant and equipment.
GKH series siphonic centrifuge is especially used in the occasion of the higher production, lower moisture in residue of the cake and sufficient washing.
It is widely used in industry area of the solid-liquid separation of the raw material and intermediate products, such as foodstuff, pharmacy, chemical, national defence and so on.
|VC natrium||Calcium phosphate|
1 . Compliance to delivery lead time
2 . 12 months guarantee period from machine arriving date.
3 . The customer could get trained by our experienced tecnician
4 . We always keep certain inventory level of spare parts, which means the replacement can be sent to you timely
Contact Person: Lee